Samsung Galaxy Note 10.1 N8013 gets pre-rooted Android 4.1.1 Jelly Bean UECLK8 firmware update [Tutorial]

Samsung Galaxy Note 10.1 with model N8013 owners can now update their device to run a pre-rooted Android 4.1.1 Jelly Bean firmware with N8013UECLK8 build. ClockworkMod Recovery will be required for the flashing of this ROM. Not only does it bring Jelly Bean features into the tablet, the firmware is also pre-rooted so all Samsung-specific apps and functionality remain intact. Before you follow our step-by-step tutorial on how to flash this firmware, be sure you read our warning, disclaimer and reminders.

Warning: The N8013UECLK8 Android 4.1.1 Jelly Bean firmware is for Galaxy Note 10.1 with model number N8013 only. Please check the model of you device before flashing: go Settings => About phone.

Reminders

1. Fully-charge your device?s battery before flashing, or make sure it has at least 80% battery left.
2. Backup EFS folder.
3. Enable USB Debugging.
4. Your devices should be rooted prior to doing this tutorial.
5. The ClockworkMod Recovery (CWM) should be installed because it will be used to flash the firmware.
6. Make sure all necessary USB drivers are installed so the device can be detected without problems.

Tutorial

Step 1: Connect your Galaxy Note 10.1 to your computer using the original USB data cable. Make sure the device is properly detected before you proceed to the next step.

Step 2: Download the update (N8013-UECIK8-ARCLK8-XAR-deodexed.zip) into the root directory of your device?s internal memory, or, you can download it to your computer and copy the package to your device, whichever your prefer. You don?t need to extract it because CWM needs it intact and zipped.

Step 3: Once downloaded/copied the package into your device, you can now disconnect it from your computer and turn it off.

Step 4: Boot your device into ClockworkMod Recovery mode: press and hold VOLUME UP? and POWER buttons together until CWM screen appears. You can use volume buttons to navigate through each option and power button to select.

Step 5: So that you can revert to your current firmware if things go bad, it is advisable you make a Nandroid backup of your current ROM: choose option Backup and Restore => Backup.

Step 6: Going back to the main recovery menu, choose Wipe Data/Factory Reset => Yes to perform full data wipe. It may take a few minutes to complete.

Step 7: After the full data wipe, you are now ready to flash the pre-rooted firmware: choose Install zip from SD card => Choose zip from SD card and browse through your device?s internal memory and find N8013-UECIK8-ARCLK8-XAR-deodexed.zip file. Confirm your action by choosing Yes in the next screen.

Step 8: It is recommended you perform full data wipe again after the firmware is flashed into your device. Follow step 7.

Step 9: You may now reboot your device by selecting Reboot System Now from the main menu. Your device will boot longer than usual this time but the next time you reboot it would be like before. So, you need to wait a little longer.

Disclaimer: The Droid Guy cannot be held responsible for any damages in your device. Flash the firmware at your own risk.

[source: xda developers]

Tags: Android 4.1.1 Jelly Bean UECLK8, Samsung Galaxy Note 10.1 N8013

Category: Android, How To, Samsung, Tablets

Source: http://thedroidguy.com/2013/01/samsung-galaxy-note-10-1-n8013-gets-pre-rooted-android-4-1-1-jelly-bean-ueclk8-firmware-update-tutorial/?utm_source=rss&utm_medium=rss&utm_campaign=samsung-galaxy-note-10-1-n8013-gets-pre-rooted-android-4-1-1-jelly-bean

taio cruz Winter Olympics 2014 powerball numbers freddie mercury Horshack Beady Eye Eric Idle